微波耦合铁碳微电解预处理石化废水的试验

采用微波耦合铁碳微电解技术对石化废水进行预处理,并对预处理前后水样中有机物的变化进行分析。结果表明,原水CODCr为10 500 mg/L,在废水pH值为3、铁碳投加量为20%、微波功率为700 W,经微波辐射5 min处理后,出水CODCr为2 370 mg/L左右,COD去除率稳定在77%左右,提高了废水的可生化性。GC-MS和三维荧光分析结果均表明,微波耦合铁碳微电解处理后,试验废水中有机物的数量及浓度大幅降低。结合后续生化处理,可以达到三级污水综合排放标准(GB 8978-1996)。微波耦合铁碳微电解可作为石化废水的有效预处理方法。     

Magnetoelectric,magnetodielectric effect and dielectric,magnetic properties of microwave-sintered lead-free x(Co0.9Ni0.1Fe2O4)-(1-x)[0.5(Ba0.7Ca0.3TiO3)-0.5(BaZr0.2Ti0.8O3)] particulate multiferroic composite

Materials with two distinct (magnetostrictive-ferroelectric) phases, i.e., x (Co_0·9Ni_0·1Fe₂O₄) -(1-x) [0.5 (Ba_0·7Ca_0·3TiO₃) −0.5 (BaZr_0·2Ti_0·8O₃)], combined at ratios of 10:90, 20:80, 30:70, and 40:60 were prepared using a hydroxide coprecipitation method. These multiferroic composites were subjected to sintering via the hybrid microwave sintering technique at 1200 °C for 20 min. Ni-substituted CFO exhibited excellent magnetic properties at room temperature, with Ms ≈ 80 emu/g, μB ≈ 3.37, Mr ≈ 19.05 emu/g, and Hc ≈ 599 Oe, as well as a high value of the magnetostriction coefficient (λ12 ≈ −118 ppm). The magnetostrictive-ferroelectric crystal phases in each composite were confirmed via X-ray diffraction analysis. The highest value of the linear magneto-electric coefficient was α = 21.6 mV/cm-Oe at a frequency of 1 kHz for the 40CNFO-60(BCT-BZT) composite, and a similar sample had the highest value of the magnetodielectric coefficient, which was approximately 3.3% at f = 1 kHz with an applied magnetic field of 1 T. The typical ferromagnetic and ferroelectric nature of each composite was confirmed by M − H and P–E hysteresis loops, respectively at room temperature. Two anomalies were observed in the temperature-dependent dielectric permittivity one at ~140 °C and another above 500 °C confirming the coexistence of two materials with distinct transition points, i.e., BCT-BZT and CNFO, respectively.     

锡石多金属硫化矿微波助磨试验研究

本文以广西某选矿厂锡石多金属硫化矿矿石为原料,研究了微波预处理对矿石磨矿产物粒度组成、磨矿动力学、破碎速率及磨机生产能力的影响。结果表明,微波预处理后,矿石在不同磨矿时间下的磨矿产物粒度均变细,-0.074mm粒级含量提高了4.41%~12.90%；微波预处理前后该矿石磨矿均符合一级磨矿动力学模型；微波预处理使矿石的破碎速率(S₁)值提高近57%,且磨机的生产能力得到了明显提升。因此,微波预处理可以降低矿石的强度,强化矿石的磨矿过程,是一种有效的降低磨矿能耗、提高磨矿效率的方法。     

复杂流道结构料仓的下料流率预测

在实验室搭建的有机玻璃料仓下料平台上，分别以自由流动粉体玻璃微珠和黏附性粉体煤粉和聚氯乙烯为实验介质，针对无改流体(No-In)、封闭改流体(Con-In)和开放改流体(Ucon-In)三种情况所形成的不同流道结构，开展了粉体料仓下料及其流率建模研究，定量分析了改流体对粉体下料流率的促进作用，对比给出了玻璃微珠、煤粉和聚氯乙烯在不同流道结构料仓内的下料特性。研究表明，改流体的引入有利于提高料仓下料流率，Con-In促进流动效果最明显，对于流动性弱的煤粉，下料流率提升幅度达到最大的58%。基于剪切摩擦区的概念，提出流率校正因子F对最小能量理论方程进行了修正，将理想的料仓下料模型拓展至实际下料过程。进一步，对于Con-In，根据流道结构特征结合对粉体的受力分析，修正了模型中的锥角项；对于Ucon-In，基于粉体下料流动竞争机制，提出分阶段下料模式并关联了内层和夹层的下料流率，最终建立了复杂流道结构料仓的下料流率预测模型。该模型综合考虑了粉体物性、下料流型和流道结构的影响，可有效预测自由流动粉体和黏附性粉体流经传统料仓(No-In)和改流体料仓(包括Con-In和Ucon-In)的粉体下料流率，且预测偏差<10%。     

微波加热CO2活化法制备生物质活性炭及其脱硫性能研究

以富含含氮官能团的大豆秸秆为原料前体，结合微波加热的特殊优势，将微波加热技术应用于大豆秸秆热解和活化工艺。以热解固体产物为活化原料，以CO₂为活化剂进行活性炭制备研究，以期制备出高脱硫性能的生物质活性炭。首先通过正交实验设计及极差分析得出最优活化水平，再通过单因素实验法考察微波功率、CO₂流量和活化时间对活性炭产率、孔隙结构以及脱硫性能的影响。对比分析选出最佳活化条件为微波功率900 W，CO₂流量0.10 L/min，活化时间20 min。在此条件下活性炭产率为76.3%（质量），SO₂饱和吸附容量为112.56 mg/g，比表面积为466.28 m²/g。相比热解炭，活性炭的比表面积更大，孔隙更加丰富，脱硫性能显著提高。     

Investigation on SCR-based ESD protection device for biomedical integrated circuits in a 0.18-μm CMOS process

In these decades, integrated circuits for biomedical electronics applications have been designed and implemented in CMOS technologies. In order to be safely used by human, all microelectronic products must meet the reliability specifications. Therefore, electrostatic discharge (ESD) must be taken into consideration. To protect the biomedical integrated circuits in CMOS technologies from ESD damage, a dual-directional silicon-controlled rectifier (DDSCR) device was presented in this work. Experimental results show that the DDSCR has the advantages of high ESD robustness, low leakage, large swing tolerance, and good latchup immunity. The DDSCR was suitable for ESD protection in biomedical integrated circuits.     

“微波技术”课程中的探究式教学

本文以电子电气类专业基础课"微波技术"为目标课程,探索探究式教学在课程中的作用和应用。在课程教学过程中,通过选择合适的切入点,尝试设置简单的探索问题,引导学生进行探究,进一步引起并保持学生对课程的兴趣,调动学生自主学习的积极性。本文对探究式教学的尝试希望可以成为本专业教师教学时的有效参考。     

Microwave assisted water extraction of plant compounds

The development of environmentally friendly processes with limited generation of polluting streams to attain sustainable utilization of raw materials is encouraged. The implementation of novel extraction technologies more efficient, selective and with lower energy consumption than conventional ones, can help in achieving this objective. Particularly promising are aqueous based methods, since water is a cheap, safe and abundant solvent and the limited use of toxic organic solvents is a consumer's, ecological and processing demand. The benefits and the limiting aspects of microwave assisted water extraction, either adding water as the only solvent or in solvent free processes, using the naturally present water in vegetal materials for the extraction of valuable components from renewable vegetal sources are highlighted and the potential of this technique for industrial applications is discussed. © 2014 Society of Chemical Industry     

超细粉体抑爆装置瞬态喷射特征参数

在敞开空间开展了容积为2 L及5 L的超细粉体抑爆装置瞬态喷射参数研究，重点介绍了5种典型装配条件下的喷射性能，并对相关特征参数进行定量分析。结果表明：抑爆剂喷射所形成的超细粉体云幕特性由气体发生器装配结构和膜片开启压力共同决定，但两者之间必须恰当配置，作用在膜片上的能量份额较大时，膜片开启状态恶化，抑爆器腔体聚压不足，抑爆剂二次喷射严重，反之膜片不能正常开启。装配优化后的I型抑爆器在触发后10 ms内腔体聚压达到峰值，膜片破裂后5 ms内抑爆剂全部喷射，喷射动态性能较好，在第1个100 ms内扩散速度达到15 m/s，在第2个100 ms内扩散速度约13 m/s，0~1 000 ms内平均扩散速度约8 m/s，扩散过程较为连续，不存在二次喷射现象，喷射距离可达到7.5 m，抑爆剂质量分布呈渐进增长，产生的超细粉体云幕特征参数优良。Ⅱ型抑爆器两种装配的喷射表明：当抑爆装置中压力上升历程及压力峰值较为接近时，抑爆剂粉体喷射特性无显著差异。上述结论的可重复性得到了数百次喷射实验的验证。     

Optimizing the lignin based synthesis of flexible polyurethane foams employing reactive liquefying agents

The present work is focused on the optimization of a green process based on the employment of by‐products obtained from wood treatments as raw materials for producing flexible polyurethane foams. More specifically, lignin was employed in flexible polyurethane foams in order to partially replace the usual fossil polyols; therefore glycerol (GLY) and glycerin polyglycidyl ether (EJ 300) were used as the polyol fraction for lignin liquefaction. Polypropylene glycol triol was used as a chain extender in different ratios with liquefaction solvents, and polymeric diphenylmethane diisocyanate as an isocyanate fraction. Liquefaction of lignin was performed by microwave irradiation, thus reducing the processing time and energy required compared to present industrial production processes. All the foams were produced in controlled expansion through the adoption of a ‘one‐shot’ approach, using water as a blowing agent and with an isocyanate index (NCO/OH) of less than 100 to improve the flexibility of the foam. This approach allowed for the substitution of up to 12% of common petro derived polyol with commercial soda lignin. Finally, the foams were characterized, presenting properties that could be modulated as a function of lignin content, GLY/EJ 300 ratio and isocyanate index. The qualities of the foams were compatible with existing materials used for furniture and for the interiors of car seats and couches. © 2015 Society of Chemical Industry